Tailoring microstructure and mechanical properties of pectin cryogels by modulate intensity of ionic interconnection.

Porous morphology and mechanical properties determine the applications of cryogels. To understand the influence of the ionic network on the microstructure and mechanical properties of pectin cryogels, we prepared low-methoxyl pectin (LMP) cryogels with different Ca2+ concentrations (measured as R-value, ranging from 0 to 2) through freeze-drying (FD). Results showed that the R-values appeared to be crucial parameters that impact the pore morphology and mechanical characteristics of cryogels. It is achieved by altering the network stability and water state properties of the cryogel precursor. Cryogel precursors with a saturated R-value (R = 1) produced a low pore diameter (0.12 mm) microstructure, obtaining the highest crispness (15.00 ± 1.85) and hardness (maximum positive force and area measuring 2.36 ± 0.31 N and 12.30 ± 1.57 N·s respectively). Hardness showed a negative correlation with Ca2+ concentration when R ≤ 1 (-0.89), and a similar correlation with the porosity of the gel network when R ≥ 1 (-0.80). Given the impacts of crosslinking on the pore structure, it is confirmed that the pore diameter can be designed between 56.24 and 153.58 µm by controlling R-value in the range of 0-2.

Pomegranate extract in polyphosphate-fluoride mouthwash reduces enamel demineralization.

OBJECTIVES: To evaluate the anti-demineralizing effect of a mouthwash comprising pomegranate peel extract (PPE 3%), sodium trimetaphosphate (TMP 0.3%), and fluoride (F 225 ppm) in an in situ study, and to assess its irritation potential in an ex vivo study. METHODS: This double-blind crossover study was conducted in four phases with 7 days each. Twelve volunteers used palatal appliances containing enamel blocks, which were subjected to cariogenic challenges. The ETF formulation (PPE + TMP + F, pH 7.0), TF formulation (TMP + F, pH 7.0), deionized water (W, pH 7.0), and essential oil commercial mouthwash (CM, 220 ppm F, pH 4.3) were dropped onto the enamel twice daily. The percentage of surface hardness loss, integrated loss of subsurface hardness, calcium, phosphorus, and fluoride in enamel and biofilms were determined. In addition, alkali-soluble extracellular polysaccharide concentrations were analyzed in the biofilms. The irritation potential was evaluated using the hen's egg chorioallantoic membrane test through the vascular effect produced during 300-s of exposure. RESULTS: ETF was the most efficacious in preventing demineralization. It also showed the highest concentrations of calcium and phosphorus in the enamel and in the biofilm, as well as the lowest amount of extracellular polysaccharides in the biofilm. In the eggs, ETF produced light reddening, whereas CM led to hyperemia and hemorrhage. CONCLUSIONS: The addition of PPE to formulations containing TMP and F increased its anti-demineralizing property, and this formulation presented a lower irritation potential than the CM. CLINICAL RELEVANCE: ETF can be a promising alternative alcohol-free mouthwash in patients at high risk of caries.

Effect of nanometric ß-calcium glycerophosphate supplementation in conventional toothpaste on enamel demineralization: An in vitro study.

The aim of this study was to evaluate the effects of supplementing toothpastes containing 1100 ppm F with micrometric or nanometric [beta]-calcium glycerophosphate (ß-CaGPm/ß-CaGPn) on artificial enamel demineralization, using a pH cycling model. Bovine enamel blocks (4 mm × 4 mm, n = 120) selected using initial surface hardness were randomly allocated to ten toothpaste groups (n = 12): without fluoride or ß-CaGPm or ß-CaGPn (Negative control), 1100 ppm F (1100 F), and 1100 ppm F plus 0.125%, 0.25%, 0.5%, and 1.0% of ß-CaGPm or ß-CaGPn. Blocks were treated two times per day with toothpaste slurry and subjected to five pH cycles (demineralizing and remineralizing solutions) at 37 °C. The final surface hardness, percentage of surface hardness loss (%SH), cross-sectional hardness (ΔKHN), and profile analysis and lesion depth subsurface were analysed using polarized light microscopy (PLM). Fluoride (F), calcium (Ca), and phosphorus (P) concentrations were also measured. Data were analysed using ANOVA and Student-Newman-Keuls tests ([alpha] = 0.001). Blocks treated with 1100 F toothpaste containing 0.5%ß-CaGPm or 0.25%ß-CaGPn showed with reduced %SH values when compared with those treated with 1100 F alone (p < 0.001). Reduced lesion depths (ΔKHN and PLM) were observed for the slurry made up of 1100 F and 0.25%ß-CaGPn (p < 0.001). The addition of ß-CaGPm and ß-CaGPn did not influence the enamel F concentration, with the 1100 F/0.25%ß-CaGPn group exhibiting the highest Ca and P enamel concentrations (p < 0.001). Based on the findings of this in vitro study, we can conclude that the fluoride toothpaste produced a superior effect when combined at an appropriate ß-CaGP molar ratio. This effect was achieved with a lower proportion of ß-CaGP in the form of nanometric particles.

Effect of the association of microparticles and nano-sized ß-calcium glycerophosphate in conventional toothpaste on enamel remineralization: In situ study.

OBJECTIVES: This in situ study aimed to assess the remineralizing effect of a fluoride toothpaste supplemented with ß-calcium glycerophosphate in both micro (ß-CaGPm) and nano-sized forms (ß-CaGPn). METHODS: This blind and cross-over study was performed in 4 phases, each spanning 3 days. Twelve volunteers utilized palatal appliances containing four bovine enamel blocks with artificial caries lesions. Volunteers were randomly assigned to the following treatment groups: Placebo (no F-ß-CaGPm-ß-CaGPn); 1100 ppm F alone (1100F); 1100F plus 0.5% micrometric ß-CaGP (1100F-0.5%ß-CaGPm); and 1100F plus 0.25%nano-sized ß-CaGP (1100F-0.25%ß-CaGPn). Participants were instructed to brush their natural teeth with the palatal appliances in the mouth for 1 min (3 times/day), ensuring that the enamel blocks were exposed to the natural toothpaste slurries. Following each phase, evaluations were conducted to determine the percentage of surface hardness recovery (%SHR), integrated recovery of subsurface hardness (ΔIHR), profile subsurface lesion through polarized light microscopy (PLM), as well as fluoride (F), calcium (Ca), and phosphorus (P) concentrations within the enamel. Data were analyzed by ANOVA and Student-Newman-Keuls test (p < 0.001). RESULTS: Treatment with 1100F-0.25%ß-CaGPn resulted in %SHR ∼69 % and ∼40 % higher when compared to 1100F and 1100F-0.5%ß-CaGPm (p < 0.001). The reduction in lesion body (ΔIHR; PLM) was ∼40 % higher with 1100F-0.25%ß-CaGPn (p < 0.001) compared to 1100F. The addition of ß-CaGPm and ß-CaGPn did not influence enamel F concentration (p > 0.001). Treatment with 1100F-0.25%ß-CaGPn led to an increase in the concentration of Ca and P in the enamel (p < 0.001). CONCLUSION: The addition of 0.25%ß-CaGPn into 1100F formulation increased the bioavailability of calcium and phosphate, promoting a higher remineralizing effect. CLINICAL SIGNIFICANCE: Toothpaste containing 1100F-0.25%ß-CaGPn showed a potential of higher remineralization to 1100 ppm F and 1100 ppm F micrometric ß-CaGP could be a strategy for patients at caries activity.

Influence of pigment Solutions on color stability and surface properties in low-shrinkage and conventional composites.

Color stability is among the most frequent causes of restoration failures, and influences surface properties. Aim: The aim of this study was to investigate the influence of pigment solutions on low-shrinkage and conventional composites regarding changes in the physical properties of composite surfaces. Materials and Method: Specimens of four composites (Filtek Z350 XT, Point 4, N'Durance and Venus Diamond) were randomly distributed into three groups to be submitted to each of three pigment solutions (red wine, tomato sauce and coffee) in fifteen-minute daily cycles, for twenty-eight days. There were 12 groups altogether (n = 10). Color, surface roughness and hardness tests were performed. Statistical analysis includedAnalysis of variance (ANOVA) and Tukey's significance test (a = 0.05). Results: Color changes caused by the solutions did not differ significantly among Filtek Z350 XT, Venus Diamond and N'Durance. Hardness decreased significantly in Filtek Z350 XT and Venus Diamond after chemical challenge with each solution. For the composite independent factor, roughness was highest in Venus Diamond, followed by Filtek Z350 XT, Point 4 and N'Durance. Conclusions: Treatment with different pigment solutions (red wine, tomato sauce or coffee) increased stainability and decreased hardness of both low-shrinkage and conventional composites, while roughness was unaffected.

A estabilidade de cor está entre as causas mais frequentes de falhas de restauragoes, que também influenciam suas propriedades superficiais. Objetivo: O objetivo do presente estudo foi investigar a influencia de solugoes de pigmentos em compósitos convencionais e de baixa retragao, bem como alteragoes naspropriedades físicas da superficie dos compósitos. Materiais eMétodo: Amostras de cada compósito (Filtek Z350XT, Point 4, N'Durance e Venus Diamond) foram distribuidas aleatoriamente em grupos submetidos a cada solugao pigmentante (vinho tinto, molho de tomate e café) em ciclos diários de quinze minutos, durante vinte e oito dias. Assim, totalizando 12 grupos (n = 10). Foram realizados testes de cor, rugosidade superficial e dureza. A Análise Estatistica foi realizada usando Análise de variáncia (ANOVA) e o teste de significáncia de Tukey (a = 0.05). Resultados: As alteragoes de cor desencadeadas pelas solugoes investigadas nao mostraram diferenga estatisticamente significativa entre os compósitos Filtek Z350 XT, Venus Diamond e N'Durance. Os valores de dureza registrados para Filtek Z350XT e Venus Diamond diminuiram significativamente após o desafio químico com cada uma das solugoes pigmentantes. Para o fator independente compósito, Venus Diamond registrou a maior rugosidade; foi seguido por Filtek Z350XT, Point 4 e N'Durance. Conclusoes: Os tratamentos das amostras com diferentes solugoes pigmentantes (vinho tinto, molho de tomate e café) aumentaram a manchabilidade dos compósitos convencionais e de baixa retragao e diminuiram sua dureza, embora nao tenham afetado a rugosidade dos compósitos.

The effect of ascorbic acid and cranberry on the bond strength, surface roughness, and surface hardness of bleached enamel with hydrogen peroxide and zinc phthalocyanine activated by photodynamic therapy.

AIM: To evaluate the effect of different bleaching methods 40% (hydrogen peroxide) HP and Zinc Phthalocyanine (ZP) activated by photodynamic therapy (PDT) with the utilization of diverse procedures of reversal (10% ascorbic acid and 6% cranberry solution) on bond values, surface microhardness and surface roughness of bleached enamel surface. MATERIAL AND METHODS: An aggregate of 60 extracted human mandibular molars was gathered and the buccal surface of each specimen was exposed to 2 mm of enamel surface for bleaching with chemical and photoactivated agents with the use of reversal solutions. Specimens were divided into six groups (n = 10) at random- Group 1: samples bleached with 40% HP with 10% ascorbic acid (reversal agent), group 2: ZP activated by PDT with 10% ascorbic acid (reversal agent), group 3: 40% HP with 6% cranberry solution as a reversal agent, group 4: ZP activated by PDT with 6% cranberry solution, group 5: 40% HP and group 6: ZP activated by PDT with no reversal agents. Resin cement restoration was performed via etch and rinse technique and SBS was estimated by using the universal testing machine, SMH by using Vickers hardness tester, and Ra by stylus profilometer. Statistical analysis was executed using the ANOVA test and the Tukey multiple tests (p<0.05). RESULTS: Enamel surface bleached with 40% HP reversed with 10% ascorbic acid displayed the highest SBS while 40% HP with no reversal agent use showed the least SBS. For SMH, ZP activated by PDT when applied on the enamel surface and reversed with 10% ascorbic acid showed the highest SMH while when bleached with 40% HP and reversed with 6% cranberry solution showed the least SMH value. For Ra, Group 3: samples bleached with 40% HP with 6% cranberry solution as reversal agent showed the highest Ra value while bleaching of enamel surface with ZP activated by PDT with 6% cranberry displayed the least Ra value. CONCLUSION: Bleached enamel surface with Zinc Phthalocyanine activated by PDT with the application of 10% ascorbic acid as reversal solution has demonstrated the highest SBS and SMH with acceptable surface roughness for bonding adhesive resin to the enamel surface.

Host use by 2 sibling species of bogus yucca moths in relation to plant hardness and saponin content.

Plant defenses allow plants to deter or kill their insect herbivores and are considered to be a major driver of host use for herbivorous insects in both ecological and evolutionary time. Many closely related species of insect herbivores differ in their ability to respond to plant defenses and in some cases are specialized to specific plant species. Here we tested whether both mechanical and chemical plant defenses are a major factor in determining the host range of 2 sibling species of Prodoxid bogus yucca moths, Prodoxus decipiens (Riley) and Prodoxus quinquepunctellus (Chambers) that feed within the inflorescence stalk of Yucca species. These 2 moth species have separate suites of host plant species, yet narrowly overlap geographically and share 1 Yucca species, Y. glauca. We surveyed the lignin and cellulose content, the force required to the puncture the stalk tissue, and saponin concentration across 5 Yucca species used as hosts. Lignin, cellulose concentrations, and stalk hardness differed among Yucca species but did not correlate with host use patterns by the moths. Saponin concentrations in the stalk tissue were relatively low for yuccas (<1%) and did not differ among species. The results suggest that these moth species should be able to use each other's hosts for egg deposition. Additional factors such as larval development or competition among larvae for feeding space may serve to keep moth species from expanding onto plants used by its sibling species.

Properties of cell wall polysaccharides of raw nectarine fruits after treatment under conditions that modulate gastric digestion.

The results of the study of the physicochemical properties of the high-molecular-weight soluble and insoluble components of nectarine cell walls obtained by fruit treatment under conditions that modulate of gastric digestion are presented. Homogenized nectarine fruits were sequentially treated by natural saliva and simulated gastric fluid (SGF) at pH 1.8 and 3.0. The isolated polysaccharides were compared with polysaccharides obtained by sequential extraction of nectarine fruit with cold, hot, and acidified water, solutions of ammonium oxalate and sodium carbonate. As a result, high-molecular-weight water-soluble pectic polysaccharides, weakly bound in the cell wall, were dissolved in the simulated gastric fluid, regardless of pH. Homogalacturonan (HG) and rhamnogalacturonan-I (RG-I) were identified in all pectins. It was shown that their quantity and ability to form highly viscous solutions determine high values of the rheological characteristics of the nectarine mixture formed under simulated gastric conditions. The modifications occurring with the insoluble components under the influence of acidity of SGF were importance. They determined difference in the physicochemical properties of both the insoluble fibres and the nectarine mixtures.

Effect of fluoride gels with nano-sized sodium trimetaphosphate on the in vitro remineralization of caries lesions.

OBJECTIVE: To evaluate the effects of fluoride (F) gels supplemented with micrometric or nano-sized sodium trimetaphosphate (TMPmicro and TMPnano, respectively) on the in vitro remineralization of caries-like lesions. METHODOLOGY: Bovine enamel subsurface lesions (n=168) were selected according to their surface hardness (SH) and randomly divided into seven groups (n=24/group): Placebo (without F/TMP), 4,500 ppm F (4500F), 4500F + 2.5% TMPnano (2.5% Nano), 4500F + 5% TMPnano (5% Nano), 4500F + 5% TMPmicro (5% Micro), 9,000 ppm F (9000F), and 12,300 ppm F (Acid gel). The gels were applied in a thin layer for one minute. Half of the blocks were subjected to pH cycling for six days, whereas the remaining specimens were used for loosely- (calcium fluoride; CaF2) and firmly-bound (fluorapatite; FA) fluoride analysis. The percentage of surface hardness recovery (%SHR), area of subsurface lesion (ΔKHN), CaF2, FA, calcium (Ca), and phosphorus (P) on/in enamel were determined. Data (log10-transformed) were subjected to ANOVA and the Student-Newman-Keuls' test (p<0.05). RESULTS: We observed a dose-response relation between F concentrations in the gels without TMP for %SHR and ΔKHN. The 2.5% Nano and 5% Micro reached similar %SHR when compared with 9000F and Acid gels. For ΔKHN, Placebo and 5% Nano gels had the highest values, and 5% Micro, 2.5% Nano, 9000F, and Acid gels, the lowest. All groups had similar retained CaF2 values, except for Placebo and Acid gel. We verified observed an increase in Ca concentrations in nano-sized TMP groups. Regarding P, TMP groups showed similar formation and retention to 9000F and Acid. CONCLUSION: Adding 2.5% nano-sized or 5% micrometric TMP to low-fluoride gels lead to enhanced in vitro remineralization of artificial caries lesions.

In vitro effect of low-fluoride toothpaste supplemented with sodium trimetaphosphate, xylitol, and erythritol on enamel demineralization.

OBJECTIVE: Regular use of toothpaste with fluoride (F) concentrations of ≥ 1000 ppm has been shown to contribute to reducing caries increment. However, when used by children during the period of dental development, it can lead to dental fluorosis. In this study, we aimed to evaluate the in vitro effect of a toothpaste formulation with reduced fluoride (F) concentration (200 ppm) supplemented with sodium trimetaphosphate (TMP: 0.2%), Xylitol (X:16%), and Erythritol (E: 4%) on dental enamel demineralization. METHODOLOGY: Bovine enamel blocks were selected according to initial surface hardness (SHi) and then divided into seven experimental toothpaste groups (n=12). These groups included 1) no F-TMP-X-E (Placebo); 2) 16% Xylitol and 4% Erythritol (X-E); 3) 16% Xylitol, 4% Erythritol and 0.2%TMP (X-E-TMP); 4) 200 ppm F (no X-E-TMP: (200F)); 5) 200 ppm F and 0.2% TMP (200F-TMP); 200 ppm F, 16% Xylitol, 4% Erythritol, and 0.2% TMP (200F-X-E-TMP); and 7) 1,100 ppm F (1100F). Blocks were individually treated 2×/day with slurries of toothpastes and subjected to a pH cycling regimen for five days (DES: 6 hours and RE: 18 hours). Then, the percentage of surface hardness loss (%SH), integrated loss of subsurface hardness (ΔKHN), fluoride (F), calcium (Ca), and phosphorus (P) in enamel were determined. The data were analyzed by ANOVA (1-criterion) and the Student-Newman-Keuls test (p<0.001). RESULTS: We found that the 200F-X-E-TMP treatment reduced %SH by 43% compared to the 1100F treatments (p<0.001). The ΔKHN was ~ 65% higher with 200F-X-E-TMP compared to 1100F (p<0.001). The highest concentration of F in enamel was observed on the 1100F treatment (p<0.001). The 200F-X-E-TMP treatment promote higher increase of Ca and P concentration in the enamel (p<0.001). CONCLUSION: The association of 200F-X-E-TMP led to a significant increase of the protective effect on enamel demineralization compared to the 1100F toothpaste.

Dietary threonine improves muscle nutritional value and muscle hardness associated with collagen synthesis in grass carp (Ctenopharyngodon idella).

To further explain the improvement effect of threonine (Thr) on the fillet quality of fish, a 9-week feeding experiment was conducted. After feeding graded levels of Thr (2.38, 5.38, 8.38, 11.38, 14.38 and 17.38 g/kg), the compositions of fillet hydrolyzed amino acid and fatty acid, and the muscle hardness associated with collagen biosynthesis were mainly analyzed in grass carp (Ctenopharyngodon idella). The results showed that Thr increased the pH value, changed the amino acids and fatty acid composition of fillets, especially essential amino acid (EAA), C22:6n3 (DHA) and C20:5n3 (EPA). Furthermore, this study revealed for the first time that the improvement of muscle hardness by Thr was associated with collagen biosynthesis, and the TGF-ß1/Smads, LARP6a and Hsp47 regulate transcriptional processes, translation initiation and post-translational modifications in collagen biosynthesis, respectively. This study offered a basis for exploring the contribution of Thr in improving muscle quality in sub-adult grass carp.

Can acid produced from probiotic bacteria alter the surface roughness, microhardness, and elemental composition of enamel? An in vitro study.

Probiotics are live microorganisms that upon administration in adequate amounts provide various health benefits to the host. Probiotics are "lactic acid-producing bacteria" as they release large amounts of organic acids, particularly lactic acids, in their surrounding environment. Although the acids produced by probiotics are beneficial for gastrointestinal and vaginal health, the acidogenic nature of probiotics has raised concerns among dental professionals, especially concerning their effect on the enamel and dentin. Previous studies have found that probiotics can lower the pH of the saliva and cause essential elements like Calcium and Phosphorus to leach from the enamel. This can alter the surface topography of enamel and increase the risk of enamel defects. Studies have also noted that probiotic bacteria can replace cariogenic bacteria and lower the risk of tooth decay. However, the effect of acid produced by probiotics on the enamel surface remains unclear. Hence, the present study aims to evaluate the effect of probiotics on the surface roughness, microhardness, and elemental composition of enamel compared to 0.1 M Lactic acid (demineralizing agent). Twenty enamel sections were randomly divided into groups and subjected to a pH cycling model using a probiotic suspension and 0.1 M lactic acid. The changes in the surface roughness, microhardness, surface morphology, and elemental composition of the enamel with regard to Carbon, Oxygen, Sodium, Hydrogen, Magnesium, Phosphorus, Fluoride, Chlorine, and Calcium of the enamel were evaluated before and after the emersion in both the groups. The results showed a significant increase in the mean surface roughness in the probiotic group before and after the exposure. The microhardness of the enamel decreased along with altered arrangement of the enamel prisms, increased striations, scratch marks, and pitting after exposure to the probiotic group. A decrease in the atomic/weight% for Calcium, Phosphorous, Fluoride, Aluminium, and Oxygen and an increase in the weight/atomic% for Carbon, Nitrogen, and Sodium were noted compared to the baseline in the probiotic solution. The results in the probiotic group were comparable to the 0.1 M lactic acids. The pH changed from 5.78 to 3.06 at the end of 24 h in the probiotic group. Based on these findings, we conclude that exposure to probiotics can affect microhardness and surface roughness and cause leaching of essential elements like Calcium and Phosphorous from the enamel.

Effect of whitening mouthrinses on color change, whiteness change, surface roughness, and hardness of stained resin composites.

PURPOSE: To evaluate the effect of whitening mouthrinses on the color change, whiteness change, surface roughness, and hardness of stained resin composites after different immersion times. METHODS: Three different resin composites (Estelite Σ Quick, G-Aenial Anterior, Omnichroma) were used to prepare a total of 90 samples (30 samples from each resin composite). The samples were kept in coffee for 12 days, then divided into three subgroups (Control, Crest 3D White, and Listerine Advanced White; n=10 each). Color change (ΔE00) and whiteness change (ΔWID) were evaluated at time intervals of 0-24 hours (T0-T1), 0-72 hours (T0-T2), and 24-72 hours (T1-T2). Surface roughness and hardness values were evaluated at T0, T1, and T2 after immersion in mouthrinses. Two-way ANOVA (for color and whiteness changes) and generalized linear model (for surface roughness and hardness) were used for data analyses (P< 0.05). RESULTS: Omnichroma had the highest value for color change with Crest 3D White during T0-T1 and T0-T2. Crest 3D White showed better color changes than Listerine Advanced White. In all composites and mouthrinse groups, the highest and lowest values of ΔWID were at T0-T2 and T1-T2, respectively, with the highest value for Omnichroma with Crest 3D White at T0-T2 and the lowest for G-Aenial Anterior with control groups at T1-T2. The highest roughness values were found with the Omnichroma at T2. Whitening mouthrinses significantly increased roughness and decreased hardness compared to baseline. CLINICAL SIGNIFICANCE: Short-term regular use of whitening mouthrinse can recover color and increase the perception of whiteness without any significant increase in the roughness or hardness of resin composites, while long-term use affects both the roughness and hardness of resin composites.

Effect of low temperature extrusion-modified potato starch addition on properties of whole wheat dough and texture of whole wheat youtiao.

In this study, low temperature extrusion-modified potato starch (MPS) was added to improve properties of whole wheat dough and textural quality of resulted youtiao. Extrusion temperature (60, 90 ℃) and barrel moisture content (30, 42 and 54%) were set as test variables. The results suggested that the low temperature extrusion processing caused moderate gelatinization and improved gel-forming properties of potato starch. MPS addition decreased the setback by up to 46%, and enhanced the viscoelasticity of whole wheat dough significantly. Compared to the whole wheat-based youtiao, the addition of 10% MPS decreased the hardness by up to 72%, and increased the springiness and specific volume by 32% and 22%, respectively. The addition of MPS prepared at lower extrusion temperature (60 ℃) and moderate moisture content (42%) resulted in the optimum textural qualities of whole wheat youtiao. This study will help better understand the role of MPS in whole wheat-based food product.

Fracture toughness and hardness of in-office, 3D-printed ceramic brackets.

OBJECTIVES: Three-dimensional (3D) printing technology is a promising manufacturing technique for fabricating ceramic brackets. The aim of this research was to assess fundamental mechanical properties of in-office, 3D printed ceramic brackets. MATERIALS AND METHODS: 3D-printed zirconia brackets, commercially available polycrystalline alumina ceramic brackets (Clarity, 3 M St. Paul, MN) and 3D-printed customized polycrystalline alumina ceramic ones (LightForce™, Burlington, Massachusetts) were included in this study. Seven 3D printed zirconia brackets and equal number of ceramic ones from each manufacturer underwent metallographic grinding and polishing followed by Vickers indentation testing. Hardness (HV) and fracture toughness (K1c) were estimated by measuring impression average diagonal length and crack length, respectively. After descriptive statistics calculation, group differences were analysed with 1 Way ANOVA and Holm Sidak post hoc multiple comparison test at significance level α = .05. RESULTS: Statistically significant differences were found among the materials tested with respect to hardness and fracture toughness. The 3D-printed zirconia proved to be less hard (1261 ± 39 vs 2000 ± 49 vs 1840 ± 38) but more resistant to crack propagation (K1c = 6.62 ± 0.61 vs 5.30 ± 0.48 vs 4.44 ± 0.30 MPa m1/2 ) than the alumina brackets (Clarity and Light Force respectivelty). Significant differences were observed between the 3D printed and the commercially available polycrystalline alumina ceramic brackets but to a lesser extent. CONCLUSIONS: Under the limitations of this study, the 3D printed zirconia bracket tested is characterized by mechanical properties associated with advantageous orthodontic fixed appliances traits regarding clinically relevant parameters.

Effects of food hardness on temporomandibular joint osteoarthritis: Qualitative and quantitative micro-CT analysis of rats in vivo.

BACKGROUND: Temporomandibular joint osteoarthritis (TMJ-OA) is a degenerative joint disease in which quantitative analysis based on magnetic resonance image (MRI) or cone-beam computed tomography (CBCT) remains limited. Moreover, the long-term effects of soft food on the adaptive condylar remodeling process in TMJ-OA remain unclear. This study aimed to assess the effects of food hardness on adaptive condylar remodeling in a healthy TMJ, TMJ-OA, and controlled TMJ-OA. METHODS: Complete Freund's adjuvant (CFA) was used for TMJ-OA induction and Link-N (LN) for TMJ repair. Eighteen mature rats were randomly divided into six groups: (1) control/normal diet (Ctrl-N); (2) control/soft diet (Ctrl-S); (3) TMJ-OA/normal diet (CFA-N); (4) TMJ-OA/soft diet (CFA-S); (5) Link-N-controlled TMJ-OA/normal diet (LN-N); and (6) Link-N-controlled TMJ-OA/soft diet (LN-S). Micro-CT was performed 14, 21, and 28 days after CFA injection to analyze the bone volume, bone volume fraction (BVF), bone mineral density (BMD), and trabecular bone number and thickness (Tb.N, Tb.Th). MRI and histological imaging were performed to support the analysis. RESULTS: Under CFA treatment, the BVF and BMD decreased significantly (p < 0.01) and later recovered to normal. However, more significant improvements occurred in normal-diet groups than soft-diet groups. Additionally, bone volume changes were more predictable in the normal-diet groups than in the soft-diet groups. The normal-diet groups presented a significant decrease and increase in the Tb.N and Tb.Th, respectively (p < 0.05), while the Tb.N and Tb.Th in the soft-diet groups remained largely unchanged. Furthermore, a significantly higher frequency of irregularities on the condylar articular surface was found in the soft-diet groups. CONCLUSIONS: Compared with a soft diet, a normal diet may be beneficial for preserving condyle articular surface and directing bone remodeling in TMJ-OA rats.

The impact of the soluble protein fraction and kernel hardness on wheat flour starch digestibility.

Wheat is the staple crop for 35% of the world's population, providing a major source of calories, mainly in the form of starch. The digestibility of wheat starch varies between different flours and products. Wheat products that are rapidly digested elicit large post-prandial glucose peaks associated with metabolic disorders. We investigated the impact of protein on starch digestion in three commercial flours with different grain hardness. A soluble extract of wheat proteins reduced starch digestion, even following gastric proteolysis. This extract was enriched in proteinaceous α-amylase inhibitors which were partially degraded during gastric proteolysis. Starch digestion kinetic analysis was carried out for flour samples pre-treated with different pepsin activities. The rate of starch digestion was altered following pepsin pre-digestion, and the extent of starch digestion increased in response to pepsin pre-digestion. We conclude that soluble proteinaceous alpha-amylase inhibitors present in wheat can escape gastric digestion and significantly contribute to reducing starch digestion in the small intestine.

Effect of Emulsifiers on the Quality of Palm Oil Based Shortening during Variable Temperature Storage.

The quality and processing characters of shortening are strongly influenced by the temperature fluctuation during storage and handling. Some chemical components, especially the presence of emulsifiers in shortening formula might be attributed to the quality change of shortening in response to temperature fluctuation. In this work, the effect of emulsifiers on the mechanical properties, crystalline structure, and crystalline transformation of fat was investigated with a palm oil-based shortening under varied storage temperature (4°C, 12 h - 28°C, 12 h, cycle reciprocating). Results show that the shortening without emulsifiers deteriorated easily with a severe separation of liquid oil and reduction of hardness, which was owing to the aggregation of crystals, and the appearance to high proportion of ß crystals at the later stage in storage (day 7 and day 14). However, the addition of the emulsifiers such as sorbitan monopalmitate (SMP), Glyceryl monostearate (GMS), and Glycerol monopalmitate (GMP) ameliorated the production of ß crystals effectively. Among the tested emulsifiers, the shortening adding GMS showed the best quality, which remained stable in multiple cycles up to 14 times. The findings will guide the use of emulsifiers in palm fat processing.

Development of a Site-Specific Guideline Value for Copper and Aquatic Life in Tropical Freshwaters of Low Hardness.

Copper (Cu) is a contaminant of potential concern for a uranium mine whose receiving waters are in the World Heritage-listed Kakadu National Park in northern Australia. The physicochemical characteristics of the freshwaters in this region enhance metal bioavailability and toxicity. Seven tropical species were used to assess the chronic toxicity of Cu in extremely soft freshwater from a creek upstream of the mine. Sensitivity to Cu was as follows: Moinodaphnia macleayi > Chlorella sp. > Velesunio sp. > Hydra viridissima > Amerianna cumingi > Lemna aequinoctialis > Mogurnda mogurnda. The 10% effect concentrations (EC10s) ranged from 1.0 µg/L Cu for the cladoceran Moinodaphnia macleayi to 9.6 µg/L for the fish M. mogurnda. The EC50s ranged from 6.6 µg/L Cu for the mussel Velesunio sp. to 22.5 µg/L Cu for M. mogurnda. Geochemical modeling predicted Cu to be strongly bound to fulvic acid (80%-99%) and of low bioavailability (0.02%-11.5%) under these conditions. Protective concentrations (PCs) were derived from a species sensitivity distribution for the local biota. The 99% PC (PC99), PC95, PC90, and PC80 values were 0.5, 0.8, 1.0, and 1.5 µg/L Cu, respectively. These threshold values suggest that the current Australian and New Zealand default national 99% protection guideline value for Cu (1.0 µg/L) would not provide adequate protection in freshwaters of low hardness, particularly for this area of high conservation value. The continuous criterion concentration predicted by the Cu biotic ligand model for conditions of low pH (6.1), low dissolved organic carbon (2.5 mg/L), low hardness (3.3 mg/L), and 27 °C was 0.48 µg/L Cu, comparable with the PC99. Consideration of the natural water quality conditions of a site is paramount for protective water quality guidelines. Environ Toxicol Chem 2022;41:2808-2821. © 2022 Commonwealth of Australia. Environmental Toxicology and Chemistry © 2022 SETAC.

Influence of the self-adhering strategy on microhardness, sorption, solubility, color stability, and cytotoxicity compared to bulk-fill and conventional resin composites.

OBJECTIVES: To analyze and compare, in vitro, the microhardness, sorption, solubility, color stability, and cytotoxicity of three types of resin composites: self-adhesive (SARC) (Dyad Flow (DF)/Kerr), bulk-fill (Filtek Bulk Fill Flow (FBF)/3 M ESPE), and conventional (Filtek Z350XT Flow (Z350)/3 M ESPE). MATERIALS AND METHODS: Thirty cylindrical specimens were prepared using a split metal mold (15 mm × 1 mm), divided into 3 groups (n = 10) according to the material used. Vickers hardness (VH) was calculated from three indentations (300gf/15 s) per specimen. The sorption and solubility were measured according to the ISO 4049:2009 specification after storing in distilled water for 7 days. The color of each resin composite was measured using a portable digital spectrophotometer according to the CIELAB system. After a 7-day immersion in coffee, the color variation (∆E) was calculated. Following the ISO 10993:2012, the cytotoxicity in Vero cells was evaluated through the MTT assay. The results were analyzed using the Kruskal-Wallis test to compare the studied groups. The Wilcoxon test was used to compare the assessments in each studied group. For cytotoxicity analysis, the data were compared by the ANOVA test (α = 0.05). RESULTS: DF showed the lowest VH (28.67), highest sorption (0.543 µg/mm3) and solubility (1.700 µg/mm3), and higher ∆E after 7 days of coffee immersion (p = 0.008). The resin composites studied were considered non-cytotoxic. CONCLUSIONS: The SARC presented inferior mechanical and physical-chemical properties than bulk-fill and conventional resin composites, with comparable cytotoxicity against Vero cells. CLINICAL RELEVANCE: The simplification of the clinical protocol of SARC can minimize the number of possible failures during the restorative technique. However, considering their inferior physical and mechanical properties, their coverage with materials of higher mechanical properties and physical-chemical stability should be considered.